[Bugme-new] [Bug 4243] New: Asus M6Ne Battery not supported
bugme-daemon at osdl.org
bugme-daemon at osdl.org
Wed Feb 23 10:12:52 PST 2005
http://bugme.osdl.org/show_bug.cgi?id=4243
Summary: Asus M6Ne Battery not supported
Kernel Version: 2.6.8 or 2.6.10
Status: NEW
Severity: normal
Owner: acpi_power-battery at kernel-bugs.osdl.org
Submitter: henryju at yahoo.fr
Distribution: Mandrake 10.2
Hardware Environment: Asus Laptop M6BCE16-RW
Software Environment:
Problem Description: The current state of the battery is not supported.
acpi -V
Thermal 1: ok, 63.0 degrees C
AC Adapter 1: off-line
cat /proc/acpi/battery/BAT0/info
present: yes
design capacity: 4300 mAh
last full capacity: 4063 mAh
battery technology: rechargeable
design voltage: 14800 mV
design capacity warning: 130 mAh
design capacity low: 21 mAh
capacity granularity 1: 52 mAh
capacity granularity 2: 2418 mAh
model number: M6NE
serial number: 00001
battery type: LIon
OEM info: ASUSTek
cat /proc/acpi/battery/BAT0/state
present: yes
ERROR: Unable to read battery status
dmesg -s40000
Linux version 2.6.10-1mdk (apatard at n1.mandrakesoft.com) (gcc version 3.4.3
(Mandrakelinux 10.2 3.4.3-3mdk)) #1 Fri Jan 14 14:31:03 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff40000 (usable)
BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data)
BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 130880
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126784 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f5df0
ACPI: RSDT (v001 A M I OEMRSDT 0x09000407 MSFT 0x00000097) @ 0x1ff40000
ACPI: FADT (v001 A M I OEMFACP 0x09000407 MSFT 0x00000097) @ 0x1ff40200
ACPI: OEMB (v001 A M I OEMBIOS 0x09000407 MSFT 0x00000097) @ 0x1ff50040
ACPI: DSDT (v001 1ABSP 1ABSP001 0x00000001 MSFT 0x02000001) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Built 1 zonelists
Found and enabled local APIC!
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
Kernel command line: BOOT_IMAGE=MDK_2610-1 ro root=305 acpi=on resume=/dev/hda6
splash=silent
bootsplash: silent mode.
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 600.241 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 514768k/523520k available (1903k kernel code, 8268k reserved, 546k data,
220k init, 0k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1187.84 BogoMIPS (lpj=593920)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: afe9fbbf 00000000 00000000 00000000
CPU: After vendor identify, caps: afe9fbbf 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbbf 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found.
ACPI: setting ELCR to 0200 (from 0c30)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 271k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI-0265: *** Error: Region EmbeddedControl(3) has no handler
ACPI-1138: *** Error: Method execution failed [\_SB_.PCI0.SBRG.EC0_.ACS_]
(Node c14e94c0), AE_NOT_EXIST
ACPI-1138: *** Error: Method execution failed [\_SB_.AC__._INI] (Node
c14e9ec0), AE_NOT_EXIST
ACPI-0265: *** Error: Region EmbeddedControl(3) has no handler
ACPI-1138: *** Error: Method execution failed [\_SB_.PCI0.SBRG.EC0_.BATS]
(Node c14e94a0), AE_NOT_EXIST
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._STA] (Node
c14ec1a0), AE_NOT_EXIST
ACPI-0158: *** Error: Method execution failed [\_SB_.BAT0._STA] (Node
c14ec1a0), AE_NOT_EXIST
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Enabled i801 SMBus device
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 28)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 6 7 11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs *10 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs *5 6 10)
ACPI: PCI Interrupt Link [LNKE] (IRQs 6 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 7) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 4 7) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 6 *10 12)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
pnp: 00:08: ioport range 0x480-0x48f has been reserved
pnp: 00:08: ioport range 0x5c0-0x5cf has been reserved
pnp: 00:0c: ioport range 0x540-0x55f has been reserved
pnp: 00:0c: ioport range 0x400-0x47f could not be reserved
pnp: 00:0c: ioport range 0x480-0x48f has been reserved
pnp: 00:0c: ioport range 0x500-0x53f has been reserved
pnp: 00:0c: ioport range 0x4c0-0x4cf has been reserved
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1109183618.696:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
vesafb: framebuffer at 0xd0000000, mapped to 0xe0880000, using 3072k, total 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:5680
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.4-2004/02/19: looking for picture.... found (1024x768, 116658
bytes, v3).
Console: switching to colour frame buffer device 101x37
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
inotify device minor=63
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 4
PCI: setting IRQ 4 as level-triggered
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 4 (level, low) -> IRQ 4
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe at suse.de) and petero2 at telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 10 (level, low) -> IRQ 10
ICH4: chipset revision 3
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IC25N060ATMR04-0, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: MATSHITAUJ-831D, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 >
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
Synaptics Touchpad, model: 1
Firmware: 4.6
180 degree mounted touchpad
Sensor: 18
new absolute packet format
Touchpad has extended capability bits
-> four buttons
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
ACPI wakeup devices:
SMBS MODM P0P2 CBC1 USB1 USB2 USB3
ACPI: (supports S0 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 220k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 0xe800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 5, io base 0xe880
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 10, io base 0xec00
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 10, pci mem 0xffaffc00
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
EXT3 FS on hda5, internal journal
Adding 1124508k swap on /dev/hda6. Priority:-1 extents:1
Asus Laptop ACPI Extras version 0.29
M6NE model detected, supported
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg,
GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 431 MBytes.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
[fglrx] module loaded - fglrx 8.10.19 [Feb 9 2005] on minor 0
Non-volatile memory driver v1.2
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ntfs: Ignoring new-style parameters in presence of obsolete ones
NTFS driver 2.1.22 [Flags: R/O DEBUG MODULE].
NTFS volume version 3.1.
loop: loaded (max 8 devices)
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins at debian.org>
ACPI: PCI interrupt 0000:02:01.2[C] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[ff9ef800-ff9effff] Max
Packet=[2048]
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
tg3.c:v3.14 (November 15, 2004)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 4 (level, low) -> IRQ 4
eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit)
10/100/1000BaseT Ethernet 00:11:d8:23:b7:49
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth1394: $Rev: 1224 $ Ben Collins <bcollins at debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ieee80211_crypt: registered algorithm 'NULL'
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 0.19
ipw2200: Copyright(c) 2003-2004 Intel Corporation
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 4 (level, low) -> IRQ 4
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0180003269993]
ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Thermal Zone [THRM] (59 C)
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
NET: Registered protocol family 17
ieee80211_crypt: registered algorithm 'WEP'
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 4 (level, low) -> IRQ 4
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49356 usecs
intel8x0: clocking to 48000
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.6
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.3
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03348a0(lo)
IPv6 over IPv4 tunneling driver
[fglrx:firegl_mmap] *ERROR* No map found!
eth3: no IPv6 routers present
eth0: no IPv6 routers present
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT0._BST] (Node
c14ec1c0), AE_AML_NO_RETURN_VALUE
cat /proc/interrupts
CPU0
0: 2252964 XT-PIC timer
1: 5447 XT-PIC i8042
2: 0 XT-PIC cascade
4: 57891 XT-PIC ipw2200, eth0, Intel 82801DB-ICH4
5: 0 XT-PIC uhci_hcd
9: 460 XT-PIC acpi
10: 2 XT-PIC uhci_hcd, ehci_hcd, ohci1394
11: 0 XT-PIC uhci_hcd
12: 365318 XT-PIC i8042
14: 12665 XT-PIC ide0
15: 19702 XT-PIC ide1
NMI: 0
LOC: 2252925
ERR: 0
MIS: 0
OEMB @ 0x1ff50040
0000: 4f 45 4d 42 53 00 00 00 01 54 41 20 4d 20 49 20 OEMBS....TA M I
0010: 4f 45 4d 42 49 4f 53 20 07 04 00 09 4d 53 46 54 OEMBIOS ....MSFT
0020: 97 00 00 00 0c 06 14 2e 00 00 04 80 40 05 10 80 ............ at ...
0030: 04 10 00 05 40 00 00 00 20 00 00 f8 ff 00 00 c0 .... at ... .......
0040: fe 00 10 00 00 00 00 00 00 00 00 00 00 00 20 00 .............. .
0050: 00 00 e0 ...
lspci -vv
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
More information about the Bugme-new
mailing list