[Bugme-new] [Bug 6649] New: Error messages in dmesg

bugme-daemon at bugzilla.kernel.org bugme-daemon at bugzilla.kernel.org
Mon Jun 5 06:05:17 PDT 2006


http://bugzilla.kernel.org/show_bug.cgi?id=6649

           Summary: Error messages in dmesg
    Kernel Version: 2.6.16
            Status: NEW
          Severity: normal
             Owner: acpi_bios at kernel-bugs.osdl.org
         Submitter: emiliano.grilli at gmail.com


Most recent kernel where this bug did not occur:
Distribution: debian /DeMuDi
Hardware Environment: HP t3120.it desktop PC
Software Environment:
Problem Description:

output of dmesg:
IC P0P4 P0P5 P0P6 P0P7 PS2K PS2M USB1 USB2 USB3 USB4 EUSB MC97 
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 1424KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
*****************************************************************************
*                                                                           *
*  REMINDER, the following debugging option is turned on in your .config:   *
*                                                                           *
*        CONFIG_DEBUG_DEADLOCKS                                             *
*                                                                           *
*  it may increase runtime overhead and latencies.                          *
*                                                                           *
*****************************************************************************
Freeing unused kernel memory: 148k freed
NET: Registered protocol family 1
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
libata version 1.12 loaded.
ata_piix version 1.04
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x9400 ctl 0x9002 bmdma 0x8000 irq 11
ata2: SATA max UDMA/133 cmd 0x8800 ctl 0x8402 bmdma 0x8008 irq 11
ata1: dev 0 cfg 49:2f00 82:3069 83:7d01 84:4023 85:3069 86:3c01 87:4023 88:203f
ata1: dev 0 ATA, max UDMA/100, 312581808 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : ata_piix
ATA: abnormal status 0x7F on port 0x8807
ata2: disabling port
scsi1 : ata_piix
  Vendor: ATA       Model: ST3160023AS       Rev: 3.43
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 < sda5 sda6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
input: PC Speaker
mice: PS/2 mouse device common for all mice
Real Time Clock Driver v1.12
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
hdb: max request size: 1024KiB
hdb: 490234752 sectors (251000 MB) w/16384KiB Cache, CHS=30515/255/63, UDMA(33)
hdb: cache flushes supported
 hdb: hdb1 hdb2 hdb3 < hdb5 hdb6 hdb7 >
hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hw_random hardware driver 1.0.0 loaded
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 5, io base 0x00009800
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915G Chipset.
agpgart: AGP aperture is 256M @ 0x0
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000a000
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
ieee1394: Initialized config rom entry `ip1394'
usb 1-2: new full speed USB device using uhci_hcd and address 2
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
wlan: 0.8.6.0 (EXPERIMENTAL)
ath_rate_sample: 1.2
ath_pci: 0.9.6.0 (EXPERIMENTAL)
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 3 (level, low) -> IRQ 3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 3, io base 0x0000a400
usb 2-2: new full speed USB device using uhci_hcd and address 2
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 10, io base 0x0000a800
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 5, io mem 0xccfffc00
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
usb 2-2: USB disconnect, address 2
usb 1-2: USB disconnect, address 2
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ohci1394: $Rev: 1313 $ Ben Collins <bcollins at debian.org>
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:03:01.0[A] -> Link [LNKE] -> GSI 7 (level, low) -> IRQ 7
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[7]  MMIO=[cffff800-cfffffff]  Max
Packet=[2048]
ACPI: PCI Interrupt 0000:03:03.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
Build date: Dec 27 2005
Debugging version (IEEE80211)
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps
36Mbps 48Mbps 54Mbps
ath0: turboG rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: H/W encryption support: WEP AES AES_CCM TKIP
ath0: mac 5.9 phy 4.3 radio 4.6
ath0: Use hw queue 1 for WME_AC_BE traffic
ath0: Use hw queue 0 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Use hw queue 8 for CAB traffic
ath0: Use hw queue 9 for beacons
Debugging version (ATH)
ath0: Atheros 5212: mem=0xcffe0000, irq=11
ACPI: PCI Interrupt 0000:03:04.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
Consumer PCM code does not work well at the moment --jk
usb 2-2: new full speed USB device using uhci_hcd and address 3
usb 1-2: new full speed USB device using uhci_hcd and address 3
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0011d8000051e481]
eth1394: $Rev: 1312 $ Ben Collins <bcollins at debian.org>
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
usb 4-1: new full speed USB device using uhci_hcd and address 2
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0
proto 2 vid 0x04E8 pid 0x323A
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver snd-usb-audio
Adding 3515360k swap on /dev/sda6.  Priority:-1 extents:1 across:3515360k
EXT3 FS on sda2, internal journal
Probing IDE interface ide1...
sbp2: $Rev: 1306 $ Ben Collins <bcollins at debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
do_settimeofday() was called!
do_settimeofday() was called!
  Vendor: Generic   Model: USB SD Reader     Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 00
Attached scsi removable disk sdb at scsi2, channel 0, id 0, lun 0
  Vendor: Generic   Model: USB CF Reader     Rev: 1.01
  Type:   Direct-Access                      ANSI SCSI revision: 00
Attached scsi removable disk sdc at scsi2, channel 0, id 0, lun 1
  Vendor: Generic   Model: USB SM Reader     Rev: 1.02
  Type:   Direct-Access                      ANSI SCSI revision: 00
Attached scsi removable disk sdd at scsi2, channel 0, id 0, lun 2
  Vendor: Generic   Model: USB MS Reader     Rev: 1.03
  Type:   Direct-Access                      ANSI SCSI revision: 00
Attached scsi removable disk sde at scsi2, channel 0, id 0, lun 3
usb-storage: device scan complete
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdb7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 17
do_settimeofday() was called!
Realtime LSM initialized (group 29, mlock=1)
ACPI: CPU0 (power states: C1[C1])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
lp: driver loaded but no devices found
ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-8762  Mon May 15 13:06:38 PDT 2006
WARNING: modprobe/2669 changed soft IRQ-flags.
 [<f952b810>] __nv_setup_pat_entries+0x13/0xaf [nvidia] (8)
 [<f952b9a2>] __nv_enable_pat_support+0x43/0x69 [nvidia] (24)
 [<f8855244>] nvidia_init_module+0x244/0x332 [nvidia] (28)
 [<c0137626>] sys_init_module+0x92/0x1b4 (20)
 [<c0103329>] syscall_call+0x7/0xb (16)
------------------------------
| showing all locks held by: |  (modprobe/2669 [dfd56cb0, 118]):
------------------------------

#001:             [f6ee3604] {(struct semaphore *)(&os_sema->wait)}
... acquired at:               os_alloc_sema+0x31/0x55 [nvidia]

BUG: modprobe/2669, lock held at task exit time!
NVRM: Trying to sleep during raised irql!!
NVRM:   are we holding a lock?
NVRM:   skipping os_delay
NVRM: Trying to sleep during raised irql!!
NVRM:   are we holding a lock?
NVRM:   skipping os_delay
NVRM: Trying to sleep during raised irql!!
NVRM:   are we holding a lock?
NVRM:   skipping os_delay
 [f6ee3604] {(struct semaphore *)(&os_sema->wait)}
.. held by:          modprobe: 2669 [dfd56cb0, 118]
... acquired at:               os_alloc_sema+0x31/0x55 [nvidia]
NVRM: Trying to sleep during raised irql!!
NVRM:   are we holding a lock?
NVRM:   skipping os_delay
NVRM: Trying to sleep during raised irql!!
NVRM:   are we holding a lock?
NVRM:   skipping os_delay
ISO 9660 Extensions: Microsoft Joliet Level 1
ISOFS: changing to secondary root
    ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]
    ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]
    ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]
    ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]
    ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]
    ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]
    ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]
    ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]
    ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]
    ACPI-0339: *** Error: Looking up [\_TZ_.THRM] in namespace, AE_NOT_FOUND
search_node dfff7800 start_node dfff7800 return_node 00000000
    ACPI-0508: *** Error: Method execution failed [\_GPE._L1C] (Node dfff7800),
AE_NOT_FOUND
    ACPI-0549: *** Error: AE_NOT_FOUND while evaluating method [_L1C] for GPE[ 0]

------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.



More information about the Bugme-new mailing list