[Bridge] challenge of year: connect to LAN using wireless-ap over bridge + unmanaged l2tpv3 tunnel + bridge? it's possible?
Jorge Pereira
jpereiran at gmail.com
Fri Aug 23 02:21:14 UTC 2013
hi everyone,
so,first it seemed a trivial question to me, but since I could not find
anybody being neither able to answer
this question nor giving a short config example. after a few sleepless
nights and exhausting all the reading
and research. here I am sharing my problem with all of you, in the hope of
some possible solution/sugestion.
or is it that this is impossible??
below my scheme/layout.
+---------------------------------------------------------+
| MAIN SERVER - 10.60.61.1 (DHCP SERVER) |
+---------------------------------------------------------+
|
+---------------------------+
| NETWORK vlan601 |
| net 10.251.0.0/16 |
| gw:10.251.0.1 |
+---------------------------+
|
+------------------------------------------------------------------+
| SERVER B (BRIDGE / unmanaged L2TPv3) - BAHIA |
+------------------------------------------------------------------+
*root at bahia:~# * ip -d addr show eth0 *# WAN*
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP qlen 1000
link/ether 00:50:56:a7:13:49 brd ff:ff:ff:ff:ff:ff
inet 200.243.1.5/24 brd 200.243.1.255 scope global eth0
inet6 fe80::250:56ff:fea7:1349/64 scope link
valid_lft forever preferred_lft forever
*root at bahia:~# * ip -d addr show eth1 *# LAN (VLAN/TRUNK)*
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP qlen 1000
link/ether 00:50:56:a7:13:4a brd ff:ff:ff:ff:ff:ff
inet6 fe80::250:56ff:fea7:134a/64 scope link
valid_lft forever preferred_lft forever
*root at bahia:~# * ip link add link eth1 name eth1.601 mtu 1500 type vlan id
601
*root at bahia:~# * ip link set dev eth1.601 up promisc on
*root at bahia:~# * ip -d addr show eth1.601
9: eth1.601 at eth1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UP
link/ether 00:50:56:a7:13:4a brd ff:ff:ff:ff:ff:ff
inet6 fe80::250:56ff:fea7:134a/64 scope link
valid_lft forever preferred_lft forever
*root at bahia:~# ** *ip route show
default via 200.243.1.254 dev eth0
200.243.1.0/24 dev eth0 proto kernel scope link src 200.243.1.5
*root at bahia:~# *
and.... we've the interface l2tpeth0 (L2TPv3) established with other node
into the internet by eth0 (WAN), plugged
with vlan601 (eth1.601) by bridge called "br-red"
*root at bahia:~#* brctl show
bridge name bridge id STP enabled interfaces
*root at bahia:~#* brctl addbr br-red
*root at bahia:~#* brctl addif br-red eth1.601
*root at bahia:~#** *ip l2tp add tunnel tunnel_id 45 peer_tunnel_id 42
udp_sport 5001 udp_dport 5000 encap udp local 200.243.1.5 remote
200.199.10.12
*root at bahia:~#** *ip l2tp add session tunnel_id 45 session_id 5196755
peer_session_id 128
*root at bahia:~#* ip link set l2tpeth0 up promisc on master br-red
*root at bahia:~#* ip link set br-red up
*root at bahia:~#* brctl show br-red
bridge name bridge id STP enabled interfaces
br-red 8000.005056a7134a no eth1.601
l2tpeth0
*root at bahia:~# *brctl showstp br-red
br-red
bridge id 8000.005056a7134a
designated root 8000.005056a7134a
root port 0 path cost 0
max age 20.00 bridge max age 20.00
hello time 2.00 bridge hello time 2.00
forward delay 15.00 bridge forward delay 15.00
ageing time 300.01
hello timer 1.06 tcn timer 0.00
topology change timer 0.00 gc timer 5.08
flags
eth1.601 (1)
port id 8001 state forwarding
designated root 8000.005056a7134a path cost 4
designated bridge 8000.005056a7134a message age timer 0.00
designated port 8001 forward delay timer 0.00
designated cost 0 hold timer 0.06
flags
l2tpeth0 (2)
port id 8002 state forwarding
designated root 8000.005056a7134a path cost 100
designated bridge 8000.005056a7134a message age timer 0.00
designated port 8002 forward delay timer 0.00
designated cost 0 hold timer 0.05
flags
*root at bahia:~# *
*
*
it's ok, my bridge "by-red" listen all traffic over my LAN (vlan 601) and
my L2TPv3 over internet. (wan)*
*
*
*
*root at bahia:~# ** *tcpdump -nve -i *br-red* "host 10.251.0.1"
tcpdump: WARNING: br-red: no IPv4 address assigned
tcpdump: listening on br-red, link-type EN10MB (Ethernet), capture size
65535 bytes
20:58:17.860060 d4:ae:52:84:37:ae > ff:ff:ff:ff:ff:ff, ethertype ARP
(0x0806), length 60: Ethernet (len 6), IPv4 (len 4), Request who-has
10.251.90.157 tell *10.251.0.1*, length 46
20:58:17.980065 d4:ae:52:84:37:ae > ff:ff:ff:ff:ff:ff, ethertype ARP
(0x0806), length 60: Ethernet (len 6), IPv4 (len 4), Request who-has
10.251.153.31 tell *10.251.0.1*, length 46
^C
7 packets captured
7 packets received by filter
0 packets dropped by kernel
*root at bahia:~# *
+-----------------------------------------------------------------------------------------+
| SERVER B (BRIDGE/L2TPv3 + WIRELESS ACCESS POINT) - RECIFE |
+-----------------------------------------------------------------------------------------+
*root at recife:~#* ip addr show eth1 *# (WAN)*
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP
qlen 1000
link/ether a0:f3:c1:a3:c4:11 brd ff:ff:ff:ff:ff:ff
inet 200.199.10.12/21 brd 200.199.10.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 fe80::a2f3:c1ff:fea3:c411/64 scope link
valid_lft forever preferred_lft forever
*root at recife:~#* ip route show
default via 200.199.10.254 dev eth1 proto static
200.199.10.0/21 dev eth1 proto kernel scope link src 200.199.10.12
192.168.1.0/24 dev br-lan proto kernel scope link src 192.168.1.1
*root at recife:~#* ip l2tp add tunnel tunnel_id 42 peer_tunnel_id 45
udp_sport 5000 udp_dport 5001 encap udp local 200.199.10.12 remote
200.243.1.5
*root at recife:~#* ip l2tp add session tunnel_id 42 session_id 128
peer_session_id 5196755
*root at recife:~#* ip link set dev l2tpeth0 up promisc on master br-red
*root at recife:~#* brctl show
bridge name bridge id STP enabled interfaces
br-lan 7fff.a0f3c1a3c40f no eth0
*root at recife:~#* brctl addbr br-red
*root at recife:~#* brctl addif br-red l2tpeth0
*root at recife:~#* brctl addif br-red wlan0
*root at recife:~#* ifconfig br-red up
*root at recife:~#* ip link set br-red up
*root at recife:~#* brctl show
bridge name bridge id STP enabled interfaces
br-lan 7fff.a0f3c1a3c40f no eth0
br-red 8000.1ae0f4a30221 no l2tpeth0
wlan0
*root at recife:~#*
*
*
*....::: RESUME :::...*
1) sorry for the long email....
2) when i'm "recife hostspot"... I can join in wireless "Recife Wireless"
from my device, but i can't receive ip from dhcp (10.60.61.1).
3) from "server A[bahia] (bridge with vlan601 network) and "server B
[recife]", i can "see/listen" the broadcast request from my
device mac "5c:95:ae:22:d6:6e" like below.
*root at bahia:~# *tcpdump -nve -i br-red "ether host ether 5c:95:ae:22:d6:6e"
00:08:52.653667 5c:95:ae:22:d6:6e > ff:ff:ff:ff:ff:ff, ethertype IPv4
(0x0800), length 342: (tos 0x0, ttl 255, id 37839, offset 0, flags [none],
proto UDP (17), length 328)
0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from
5c:95:ae:22:d6:6e, length 300, xid 0xe6f1d0a5, Flags [none]
Client-Ethernet-Address 5c:95:ae:22:d6:6e
Vendor-rfc1048 Extensions
Magic Cookie 0x63825363
DHCP-Message Option 53, length 1: Discover
Parameter-Request Option 55, length 6:
Subnet-Mask, Default-Gateway, Domain-Name-Server, Domain-Name
Option 119, Option 252
MSZ Option 57, length 2: 1500
Client-ID Option 61, length 7: ether 5c:95:ae:22:d6:6e
Lease-Time Option 51, length 4: 7776000
Hostname Option 12, length 14: "Straces-iPhone"
^C
1 packets captured
1 packets received by filter
*root at bahia:~#*
same thing result at "bridge a" (*root at recife:~#) *side...
4) the strangest thing of all and that, from bridge-b (recife). i can get
ip from dhcp/broadcast request over L2TPv3...
but without option "broadcast" i can't receive ip from dhcp (10.61.60.1)
*root at recife:~#* udhcpc -B -i br-red
udhcpc (v1.19.4) started
Sending discover...
Sending select for 10.251.157.22...
Lease of 10.251.157.22 obtained, lease time 300
udhcpc: ifconfig br-red 10.251.157.22 netmask 255.255.0.0 broadcast +
udhcpc: setting default routers: 10.251.0.1
*root at recife:~# *ip route add 200.243.1.5 via 200.199.10.254 dev eth1
*root at recife:~# *ip route show
default via 10.251.0.1 dev br-red
10.251.0.0/16 dev br-red proto kernel scope link src 10.251.157.22
200.199.10.0/21 dev eth1 proto kernel scope link src 200.199.10.12
200.243.1.5 via 200.199.10.254 dev eth1
192.168.1.0/24 dev br-lan proto kernel scope link src 192.168.1.1
*root at recife:~#* ping -c2 10.251.0.1
PING 10.251.0.1 (10.251.0.1): 56 data bytes
--- 10.251.0.1 ping statistics ---
2 packets transmitted, 0 packets received, 100% packet loss
*root at recife:~#*
5) output of tcpdump listen the bridge "br-red" request from bridge-a-natal
http://pastebin.com/t8wn3zRK
6) output of tcpdump listen the bridge "br-red" request from
bridge-b-recife http://pastebin.com/njTQfd5k
7) after several researches i found the kernel options to set like
"arp_filter", "bridge-nf-*",... but i don't have
idea which option should enable / disable. tried some combinations but
without success....
8) the DHCP-OFFER doesn't forward by "bridge-a"... problems with unicast?
multicast? arp_proxy? ....
9) we need join in the network by wireless and access the server 10.251.0.1
over bridge/l2tpv3 (unmanaged)
10) in our case, can use only L2TPv3. (may not be OpenVPN, ...)
11) all is Linux, without any iptables rules.
12) who will win a beer?! =]
Best regards,
Jorge Pereira
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.linuxfoundation.org/pipermail/bridge/attachments/20130822/8dd62dc2/attachment-0001.html>
More information about the Bridge
mailing list