[Bridge] [PATCH net-next v4] Documentation: networking: Clarify switchdev devices behavior
rdunlap at infradead.org
Thu Jan 10 21:50:23 UTC 2019
On 1/10/19 11:32 AM, Florian Fainelli wrote:
> This patch provides details on the expected behavior of switchdev
> enabled network devices when operating in a "stand alone" mode, as well
> as when being bridge members. This clarifies a number of things that
> recently came up during a bug fixing session on the b53 DSA switch
> Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
Reviewed-by: Randy Dunlap <rdunlap at infradead.org>
> Changes in v4:
> - more spelling/grammar/sentence fixes (Randy)
> Changes in v3:
> - spell checks, past vs. present use (Randy)
> - clarified some behaviors a bit more regarding multicast flooding
> - added some missing sentence about multicast snopping knob being
> dynamically turned on/off
> Changes in v2:
> - clarified a few parts about VLAN devices wrt. VLAN filtering and their
> behavior during enslaving.
> Documentation/networking/switchdev.txt | 105 +++++++++++++++++++++++++
> 1 file changed, 105 insertions(+)
> diff --git a/Documentation/networking/switchdev.txt b/Documentation/networking/switchdev.txt
> index 82236a17b5e6..dd58c957c557 100644
> --- a/Documentation/networking/switchdev.txt
> +++ b/Documentation/networking/switchdev.txt
> @@ -392,3 +392,108 @@ switchdev_trans_item_dequeue()
> If a transaction is aborted during "prepare" phase, switchdev code will handle
> cleanup of the queued-up objects.
> +Switchdev enabled network device expected behavior
> +Below is a set of defined behavior that switchdev enabled network devices must
> +adhere to.
> +Configuration less state
> +Upon driver bring up, the network devices must be fully operational, and the
> +backing driver must configure the network device such that it is possible to
> +send and receive traffic to this network device and it is properly separated
> +from other network devices/ports (e.g.: as is frequent with a switch ASIC). How
> +this is achieved is heavily hardware dependent, but a simple solution can be to
> +use per-port VLAN identifiers unless a better mechanism is available
> +(proprietary metadata for each network port for instance).
> +The network device must be capable of running a full IP protocol stack
> +including multicast, DHCP, IPv4/6, etc. If necessary, it should be program the
> +appropriate filters for VLAN, multicast, unicast etc. The underlying device
> +driver must effectively be configured in a similar fashion to what it would do
> +when IGMP snooping is enabled for IP multicast over these switchdev network
> +devices and unsolicited multicast must be filtered as early as possible into
> +the hardware.
> +When configuring VLANs on top of the network device, all VLANs must be working,
> +irrespective of the state of other network devices (e.g.: other ports being part
> +of a VLAN aware bridge doing ingress VID checking). See below for details.
> +Bridged network devices
> +When a switchdev enabled network device is added as a bridge member, it should
> +not disrupt any functionality of non-bridged network devices and they
> +should continue to behave as normal network devices. Depending on the bridge
> +configuration knobs below, the expected behavior is documented.
> +VLAN filtering
> +The Linux bridge allows the configuration of a VLAN filtering mode (compile and
> +run time) which must be observed by the underlying switchdev network
> +- with VLAN filtering turned off: frames ingressing the device with a VID that
> + is not programmed into the bridge/switch's VLAN table must be forwarded.
> +- with VLAN filtering turned on: frames ingressing the device with a VID that is
> + not programmed into the bridges/switch's VLAN table must be dropped.
> +Non-bridged network ports of the same switch fabric must not be disturbed in any
> +way, shape or form by the enabling of VLAN filtering.
> +VLAN devices configured on top of a switchdev network device (e.g: sw0p1.100)
> +which is a bridge port member must also observe the following behavior:
> +- with VLAN filtering turned off, these VLAN devices must be fully functional
> + since the hardware is allowed VID frames. Enslaving VLAN devices into the
> + bridge might be allowed provided that there is sufficient separation using
> + e.g.: a reserved VLAN ID (4095 for instance) for untagged traffic.
> +- with VLAN filtering turned on, these VLAN devices should not be allowed to
> + be created because they duplicate functionality/use case with the bridge's
> + VLAN functionality.
> +Because VLAN filtering can be turned on/off at runtime, the switchdev driver
> +must be able to re-configure the underlying hardware on the fly to honor the
> +toggling of that option and behave appropriately.
> +A switchdev driver can also refuse to support dynamic toggling of the VLAN
> +filtering knob at runtime and require a destruction of the bridge device(s) and
> +creation of new bridge device(s) with a different VLAN filtering value to
> +ensure VLAN awareness is pushed down to the HW.
> +IGMP snooping
> +The Linux bridge allows the configuration of IGMP snooping (compile and run
> +time) which must be observed by the underlying switchdev network device/hardware
> +in the following way:
> +- when IGMP snooping is turned off, multicast traffic must be flooded to all
> + switch ports within the same broadcast domain. The CPU/management port
> + should ideally not be flooded and continue to learn multicast traffic through
> + the network stack notifications. If the hardware is not capable of doing that
> + then the CPU/management port must also be flooded and multicast filtering
> + happens in software.
> +- when IGMP snooping is turned on, multicast traffic must selectively flow
> + to the appropriate network ports (including CPU/management port) and not flood
> + the switch.
> +Note: reserved multicast addresses (e.g.: BPDUs) as well as Local Network
> +Control block (188.8.131.52 - 184.108.40.206) do not require IGMP and should always
> +be flooded.
> +Because IGMP snooping can be turned on/off at runtime, the switchdev driver must
> +be able to re-configure the underlying hardware on the fly to honor the toggling
> +of that option and behave appropriately.
> +A switchdev driver can also refuse to support dynamic toggling of the multicast
> +snooping knob at runtime and require the destruction of the bridge device(s)
> +and creation of a new bridge device(s) with a different multicast snooping
More information about the Bridge