[Bugme-new] [Bug 4323] New: no cursor in console with intelfb
bugme-daemon at osdl.org
bugme-daemon at osdl.org
Thu Mar 10 10:15:05 PST 2005
http://bugme.osdl.org/show_bug.cgi?id=4323
Summary: no cursor in console with intelfb
Kernel Version: 2.6.11
Status: NEW
Severity: normal
Owner: jsimmons at infradead.org
Submitter: phil at systemausfall.org
Distribution: Debian 3.0 testing
Hardware Environment: Asus S5200N, Intel 855GME and ICH4-M Chipset
Software Environment:
Problem Description:
When using the intelfb there's no cursor displayed in console.
I added the kernel parameter: video=intelfb:1024x768-16 at 60 vga=791
vga=791 because the first parameter (1024x768...) didn't change the video mode.
The output from syslog:
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G chipsets
intelfb: Version 0.9.2
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
intelfb: 00:02.0: Intel(R) 855GME, aperture size 128MB, stolen memory 8060kB
intelfb: Non-CRT device is enabled ( LVDS port ). Disabling mode switching.
intelfb: Initial video mode is 1024x768-16 at 60.
intelfb: Changing the video mode is not supported.
>From my kernel configuration:
Device Drivers --> Graphics Support
[*] Support for frame buffer devices
<*> Intel 830M/845G/852GM/855GM/865G support
Device Drivers --> Graphics Support --> Console display driver support
<M> Framebuffer Console support
I didn't enable standard vesafb.
lsmod
Module Size Used by
i830 28928 1
drm 68116 2 i830
ipv6 270848 10
pcmcia 25992 4
dm_mod 61180 0
sd_mod 17936 0
sg 40352 0
sr_mod 18084 0
scsi_mod 139336 3 sd_mod,sg,sr_mod
cdrom 41888 1 sr_mod
thermal 13576 0
fan 4612 0
button 6800 0
ac 4996 0
battery 10244 0
pcspkr 3940 0
ipw2100 152772 0
firmware_class 10752 1 ipw2100
ieee80211 41380 1 ipw2100
ieee80211_crypt 6472 2 ipw2100,ieee80211
8139too 25984 0
mii 5248 1 8139too
ohci1394 35972 0
ieee1394 321716 1 ohci1394
yenta_socket 23432 2
rsrc_nonstatic 9472 1 yenta_socket
pcmcia_core 50596 3 pcmcia,yenta_socket,rsrc_nonstatic
8250_pci 18688 0
8250 25192 1 8250_pci
serial_core 23808 1 8250
usbhid 35008 0
snd_intel8x0 34112 1
snd_ac97_codec 78968 1 snd_intel8x0
snd_pcm_oss 54560 0
snd_mixer_oss 20736 1 snd_pcm_oss
snd_pcm 97160 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 26756 1 snd_pcm
snd 55780 8
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 10464 1 snd
snd_page_alloc 10244 2 snd_intel8x0,snd_pcm
ehci_hcd 35848 0
uhci_hcd 33552 0
usbcore 126072 4 usbhid,ehci_hcd,uhci_hcd
nls_cp437 5888 1
vfat 14464 1
fat 41884 1 vfat
nls_cp850 4992 0
nls_utf8 2176 0
evdev 9600 1
nls_iso8859_1 4224 1
nls_iso8859_15 4736 0
nls_base 7936 7
nls_cp437,vfat,fat,nls_cp850,nls_utf8,nls_iso8859_1,nls_iso8859_15
psmouse 29960 0
cpufreq_userspace 4572 0
cpufreq_powersave 1920 1
speedstep_centrino 8020 1
processor 23220 2 thermal,speedstep_centrino
freq_table 4612 1 speedstep_centrino
asus_acpi 11924 0
cpuid 3460 0
genrtc 10248 0
unix 30132 297
lspci -vvv
0000:00:00.0 Host bridge: Intel Corp. 82852/855GM Host Bridge (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 1821
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at <unassigned> (32-bit, prefetchable)
Capabilities: [40] #09 [8105]
0000:00:00.1 System peripheral: Intel Corp. 855GM/GME GMCH Memory I/O Control
Registers (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 182a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:00.3 System peripheral: Intel Corp. 855GM/GME GMCH Configuration Process
Registers (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 182b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:02.0 VGA compatible controller: Intel Corp. 82852/855GM Integrated
Graphics Device (rev 02) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 1712
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 169
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at feb00000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at dc00 [size=8]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.1 Display controller: Intel Corp. 82852/855GM Integrated Graphics
Device (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 1712
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at fea80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 1828
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 169
Region 4: I/O ports at d480 [size=32]
0000:00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 1828
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 185
Region 4: I/O ports at d800 [size=32]
0000:00:1d.2 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 1828
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 177
Region 4: I/O ports at d880 [size=32]
0000:00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI
Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 1829
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 193
Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [2080]
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 83) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe700000-fe8fffff
Prefetchable memory behind bridge: de500000-de6fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage
Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 1828
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 1f800000 (32-bit, non-prefetchable) [size=1K]
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
Subsystem: Asustek Computer, Inc.: Unknown device 1803
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 201
Region 0: I/O ports at e000 [size=256]
Region 1: I/O ports at e100 [size=64]
Region 2: Memory at 1f800400 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at 1f800600 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1f.6 Modem: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem
Controller (rev 03) (prog-if 00 [Generic])
Subsystem: Asustek Computer, Inc.: Unknown device 1826
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 201
Region 0: I/O ports at e200 [size=256]
Region 1: I/O ports at e300 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:03.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ac)
Subsystem: Asustek Computer, Inc.: Unknown device 1824
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 201
Region 0: Memory at 1f801000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=01, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 1fc00000-1ffff000 (prefetchable)
Memory window 1: 20000000-203ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:01:03.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ac)
Subsystem: Asustek Computer, Inc.: Unknown device 1824
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 177
Region 0: Memory at 1f802000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=01, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 20400000-207ff000 (prefetchable)
Memory window 1: 20800000-20bff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:01:03.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev
04) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 1827
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin C routed to IRQ 169
Region 0: Memory at fe8ff000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
0000:01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Asustek Computer, Inc.: Unknown device 1045
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at fe8ff800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:05.0 Network controller: Intel Corp. PRO/Wireless LAN 2100 3B Mini PCI
Adapter (rev 04)
Subsystem: Intel Corp. MIM2000/Centrino
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 8500ns max), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 177
Region 0: Memory at fe8fe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Steps to reproduce:
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
More information about the Bugme-new
mailing list