[Bugme-new] [Bug 6651] New: patch-2.6.16.16-17: VIA IRQ Fixup
broken, results in problems with USB
bugme-daemon at bugzilla.kernel.org
bugme-daemon at bugzilla.kernel.org
Mon Jun 5 07:00:08 PDT 2006
http://bugzilla.kernel.org/show_bug.cgi?id=6651
Summary: patch-2.6.16.16-17: VIA IRQ Fixup broken, results in
problems with USB
Kernel Version: 2.6.16.17
Status: NEW
Severity: normal
Owner: greg at kroah.com
Submitter: s.kockrick at web.de
Most recent kernel where this bug did not occur: 2.6.16.17
Distribution: Debian Etch, vanilla kernel from ftp.kernel.org
Hardware Environment: Laptop Sony VAIO PCG-FR215E (AMD Athlon)
Software Environment:
Problem Description: Kernel 2.6.16.16 works fine. Starting with 2.6.16.17, there
are following messages on boot:
ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Controller is probably using the
wrong IRQ.
usb 1-1: device not accepting address 2, error -110
usb 1-1: new high speed USB device using ehci_hcd and address 3
usb 1-1: device not accepting address 3, error -110
[....]
several further addresses are probed in ascending order, always with same result
(error).
This bug is probably related to the patch of drivers/pci/quirk.c in
patch-2.6.16.16-17. I tried to re-insert the line
'DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq);'
after
'DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_5,
quirk_via_irq);'
(line no. 658). With this change, the machine booted as usual, without problems.
But i am not a programmer and have no idea what i did ;-)
Output of lspci -vvv:
------------ lspci -vvv -----------------
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3-
Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333
AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e1000000-e1ffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 1400 [size=256]
Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=512]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0e.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev aa)
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 38000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 30000000-31fff000 (prefetchable)
Memory window 1: 32000000-33fff000
I/O window 0: 00002000-000020ff
I/O window 1: 00002400-000024ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:0e.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev aa)
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 9
Region 0: Memory at 38001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 34000000-35fff000 (prefetchable)
Memory window 1: 36000000-37fff000
I/O window 0: 00002800-000028ff
I/O window 1: 00002c00-00002cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:0e.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev
02) (prog-if 10 [OHCI])
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 255
Region 0: Memory at e0000800 (32-bit, non-prefetchable) [disabled] [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1020 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 64, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 9
Region 4: I/O ports at 1040 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1060 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20
[EHCI])
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin D routed to IRQ 9
Region 0: Memory at e0000400 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 11
Region 0: I/O ports at 1800 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem
Controller (rev 80)
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 255
Region 0: I/O ports at 1c00 [disabled] [size=256]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 420
Go] (rev a3) (prog-if 00 [VGA])
Subsystem: Sony Corporation: Unknown device 8143
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e1000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Region 2: Memory at f0000000 (32-bit, prefetchable) [size=512K]
Expansion ROM at f0080000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3-
Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4
-------------End of lspci -vvv -------
Output of /proc/interrupts:
CPU0
0: 600906 XT-PIC timer
1: 5939 XT-PIC i8042
2: 0 XT-PIC cascade
7: 585 XT-PIC parport0
8: 4 XT-PIC rtc
9: 119738 XT-PIC acpi, ehci_hcd:usb1, uhci_hcd:usb3, yenta, eth0
11: 127662 XT-PIC uhci_hcd:usb2, uhci_hcd:usb4, yenta, VIA8233,
nvidia
12: 1546 XT-PIC i8042
14: 22039 XT-PIC ide0
15: 18751 XT-PIC ide1
NMI: 0
LOC: 600852
ERR: 92
MIS: 0
Output of /proc/iomem:
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cfbff : Video ROM
000f0000-000fffff : System ROM
00100000-1feeffff : System RAM
00100000-002b48e8 : Kernel code
002b48e9-00364c23 : Kernel data
1fef0000-1fefbfff : ACPI Tables
1fefc000-1fefffff : ACPI Non-volatile Storage
1ff00000-1fffffff : reserved
30000000-31ffffff : PCI CardBus #02
32000000-33ffffff : PCI CardBus #02
34000000-35ffffff : PCI CardBus #06
36000000-37ffffff : PCI CardBus #06
38000000-38000fff : 0000:00:0e.0
38000000-38000fff : yenta_socket
38001000-38001fff : 0000:00:0e.1
38001000-38001fff : yenta_socket
e0000000-e00001ff : 0000:00:0c.0
e0000000-e00001ff : 8139too
e0000400-e00004ff : 0000:00:10.3
e0000400-e00004ff : ehci_hcd
e0000800-e0000fff : 0000:00:0e.2
e1000000-e1ffffff : PCI Bus #01
e1000000-e1ffffff : 0000:01:00.0
e1000000-e1ffffff : nvidia
e8000000-efffffff : 0000:00:00.0
f0000000-f7ffffff : PCI Bus #01
f0000000-f007ffff : 0000:01:00.0
f0080000-f009ffff : 0000:01:00.0
f4000000-f7ffffff : 0000:01:00.0
f4000000-f4ffffff : vesafb
fffe0000-ffffffff : reserved
Output of /proc/ioports:
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vesafb
03f6-03f6 : ide0
04d0-04d1 : pnp 00:06
0cf8-0cff : PCI conf1
1000-100f : 0000:00:11.1
1000-1007 : ide0
1008-100f : ide1
1020-103f : 0000:00:10.0
1020-103f : uhci_hcd
1040-105f : 0000:00:10.1
1040-105f : uhci_hcd
1060-107f : 0000:00:10.2
1060-107f : uhci_hcd
1400-14ff : 0000:00:0c.0
1400-14ff : 8139too
1800-18ff : 0000:00:11.5
1800-18ff : VIA8233
1c00-1cff : 0000:00:11.6
2000-20ff : PCI CardBus #02
2400-24ff : PCI CardBus #02
2800-28ff : PCI CardBus #06
2c00-2cff : PCI CardBus #06
8000-807f : 0000:00:11.0
8000-807f : motherboard
8000-8003 : PM1a_EVT_BLK
8004-8005 : PM1a_CNT_BLK
8008-800b : PM_TMR
8010-8015 : ACPI CPU throttle
8020-8023 : GPE0_BLK
8100-810f : 0000:00:11.0
8100-8107 : vt596_smbus
Steps to reproduce:
- Install kernel 2.6.16.17 (on this machine)
- reboot with USB2.0 devices connected
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
More information about the Bugme-new
mailing list