[Bugme-new] [Bug 6654] New: USB 2.0 high speed mode (ehci_hcd
module) won't work without acpi=noirq
bugme-daemon at bugzilla.kernel.org
bugme-daemon at bugzilla.kernel.org
Mon Jun 5 11:38:08 PDT 2006
http://bugzilla.kernel.org/show_bug.cgi?id=6654
Summary: USB 2.0 high speed mode (ehci_hcd module) won't work
without acpi=noirq
Kernel Version: 2.6.16.18
Status: NEW
Severity: normal
Owner: acpi_config-interrupts at kernel-bugs.osdl.org
Submitter: surgpub at telkomsa.net
Most recent kernel where this bug did not occur: None that I tested
Distribution: Kubuntu Breezy
Hardware Environment: Epox KT400A motherboard (VT8377 VT8277)
Software Environment: kernel 2.6.12.6 and 2.6.16.18 both affected
Problem Description: USB 2.0 high speed mode (ehci_hcd module) won't work
because ACPI IRQ routing messes things up. Booting with acpi=noirq works around
the bug. Before and after dmesg logs below.
dmesg (buggy)
=============
PI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:02: ioport range 0x4000-0x407f could not be reserved
pnp: 00:02: ioport range 0x5000-0x500f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e0000000-e1ffffff
PREFETCH window: d8000000-dfffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1148976392.528:1): initialized
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
0000:00:10.0: uhci_check_and_reset_hc: legsup = 0x2000
0000:00:10.0: Performing full reset
0000:00:10.1: uhci_check_and_reset_hc: legsup = 0x2000
0000:00:10.1: Performing full reset
0000:00:10.2: uhci_check_and_reset_hc: legsup = 0x2000
0000:00:10.2: Performing full reset
0000:00:10.3: uhci_check_and_reset_hc: legsup = 0x2000
0000:00:10.3: Performing full reset
Linux agpgart interface v0.101 (c) Dave Jones
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
floppy0: no floppy controllers found
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: VIA IRQ fixup for 0000:00:0f.0, from 255 to 10
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: ST3160021A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
hdd: ST340810A, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 >
hdd: max request size: 128KiB
hdd: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hdd: cache flushes not supported
hdd: hdd1 hdd2 < hdd5 > hdd3
hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
usbmon: debugfs is not available
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20
2006 UTC).
ALSA device list:
No soundcards found.
oprofile: using timer interrupt.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 5, 131072 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
ip_conntrack version 2.4 (4095 buckets, 32760 max) - 172 bytes per conntrack
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 152k freed
kjournald starting. Commit interval 5 seconds
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
Adding 2096472k swap on /dev/hdd3. Priority:-1 extents:1 across:2096472k
EXT3 FS on hda1, internal journal
lp0: using parport0 (interrupt-driven).
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL-8029 found at 0xd000, IRQ 11, 00:C0:DF:F5:1A:C9.
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
gameport: ES137x is pci0000:00:0c.0/gameport0, io 0x200, speed 962kHz
input: Microsoft SideWinder Force Feedback Pro as /class/input/input2
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: detected 2 ports
uhci_hcd 0000:00:10.0: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.0: Performing full reset
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 10, io base 0x0000dc00
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb1: SerialNumber: 0000:00:10.0
usb usb1: uevent
usb usb1: device is self-powered
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
uhci_hcd 0000:00:10.0: port 1 portsc 008a,00
hub 1-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: detected 2 ports
uhci_hcd 0000:00:10.1: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.1: Performing full reset
drivers/usb/core/inode.c: creating file '002'
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 10, io base 0x0000e000
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.1
usb usb2: uevent
usb usb2: device is self-powered
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: detected 2 ports
uhci_hcd 0000:00:10.2: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.2: Performing full reset
drivers/usb/core/inode.c: creating file '003'
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 11, io base 0x0000e400
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.2
usb usb3: uevent
usb usb3: device is self-powered
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.0: port 2 portsc 018a,00
hub 1-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: detected 2 ports
uhci_hcd 0000:00:10.3: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.3: Performing full reset
drivers/usb/core/inode.c: creating file '004'
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 11, io base 0x0000e800
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.3
usb usb4: uevent
usb usb4: device is self-powered
usb usb4: configuration #1 chosen from 1 choice
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: uevent
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.1: port 1 portsc 008a,00
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
drivers/usb/core/inode.c: creating file '001'
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.1: port 2 portsc 018a,00
hub 2-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.2: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.2: port 2 portsc 008a,00
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: reset hcs_params 0x4208 dbg=0 cc=4 pcc=2 ordered !ppc ports=8
ehci_hcd 0000:00:10.4: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.4: MWI active
drivers/usb/core/inode.c: creating file '005'
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 11, io mem 0xe2000000
ehci_hcd 0000:00:10.4: reset command 080002 (park)=0 ithresh=8 period=1024 Reset
HALT
ehci_hcd 0000:00:10.4: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: default language 0x0409
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.16.18 ehci_hcd
usb usb5: SerialNumber: 0000:00:10.4
usb usb5: uevent
usb usb5: device is self-powered
usb usb5: configuration #1 chosen from 1 choice
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: uevent
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: Single TT
hub 5-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 5-0:1.0: power on to power good time: 20ms
hub 5-0:1.0: local power source is good
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.3: port 1 portsc 008a,00
hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
drivers/usb/core/inode.c: creating file '001'
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.3: port 2 portsc 018a,00
hub 4-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
uhci_hcd 0000:00:10.0: suspend_rh (auto-stop)
uhci_hcd 0000:00:10.1: suspend_rh (auto-stop)
uhci_hcd 0000:00:10.2: suspend_rh (auto-stop)
uhci_hcd 0000:00:10.3: suspend_rh (auto-stop)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8762 Mon May 15 13:06:38 PDT 2006
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001002 POWER sig=se0 CSC
hub 5-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001002 POWER sig=se0 CSC
hub 5-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:10.4: Unlink after no-IRQ? Controller is probably using the
wrong IRQ.
usb 5-1: khubd timed out on ep0in len=18/64
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: default language 0x0409
usb 5-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-1: Product: External HDD
usb 5-1: Manufacturer: Western Digital
usb 5-1: SerialNumber: 57442D574D414E5531303836373034
usb 5-1: uevent
usb 5-1: device is self-powered
usb 5-1: configuration #1 chosen from 1 choice
usb 5-1: adding 5-1:1.0 (config #1, interface 0)
usb 5-1:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
Initializing USB Mass Storage driver...
usb-storage 5-1:1.0: usb_probe_interface
usb-storage 5-1:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: WD Model: 4000KS External Rev: 101a
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 11 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 11 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: usb-storage timed out on ep0in len=18/64
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: usb-storage timed out on ep0out len=0/0
usb 5-1: usb-storage timed out on ep0out len=0/0
usb 5-1: device not accepting address 2, error -110
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: usb-storage timed out on ep0in len=18/64
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: usb-storage timed out on ep0out len=0/0
usb 5-1: usb-storage timed out on ep0out len=0/0
usb 5-1: device not accepting address 2, error -110
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: usb-storage timed out on ep0out len=0/0
usb 5-1: usb-storage timed out on ep0out len=0/0
usb 5-1: device not accepting address 2, error -110
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: usb-storage timed out on ep0out len=0/0
usb 5-1: usb-storage timed out on ep0out len=0/0
usb 5-1: device not accepting address 2, error -110
hub 5-0:1.0: logical disconnect on port 1
hub 5-0:1.0: state 7 ports 8 chg 0002 evt 0000
hub 5-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
usb 5-1: USB disconnect, address 2
usb 5-1: usb_disable_device nuking all URBs
usb 5-1: unregistering interface 5-1:1.0
sd 0:0:0:0: scsi: Device offlined - not ready after error recovery
sd 0:0:0:0: SCSI error: return code = 0x10000
end_request: I/O error, dev sda, sector 63
FAT: unable to read boot sector
usb 5-1:1.0: uevent
usb 5-1: unregistering device
usb 5-1: uevent
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: new high speed USB device using ehci_hcd and address 3
usb 5-1: khubd timed out on ep0in len=18/64
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: khubd timed out on ep0out len=0/0
usb 5-1: khubd timed out on ep0out len=0/0
usb 5-1: device not accepting address 3, error -110
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: new high speed USB device using ehci_hcd and address 4
usb 5-1: khubd timed out on ep0in len=18/64
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: khubd timed out on ep0out len=0/0
usb 5-1: khubd timed out on ep0out len=0/0
usb 5-1: device not accepting address 4, error -110
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: new high speed USB device using ehci_hcd and address 5
usb 5-1: khubd timed out on ep0out len=0/0
ehci_hcd 0000:00:10.4: devpath 1 ep0out 3strikes
usb 5-1: device not accepting address 5, error -71
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: new high speed USB device using ehci_hcd and address 6
usb 5-1: khubd timed out on ep0out len=0/0
usb 5-1: khubd timed out on ep0out len=0/0
usb 5-1: device not accepting address 6, error -110
dmesg (acpi=noirq)
==================
le: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 515460k/524224k available (2378k kernel code, 8236k reserved, 630k data,
152k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3338.00 BogoMIPS (lpj=6676018)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000
00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2000+ stepping 01
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfbac0, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
pnp: 00:02: ioport range 0x4000-0x407f could not be reserved
pnp: 00:02: ioport range 0x5000-0x500f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e0000000-e1ffffff
PREFETCH window: d8000000-dfffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1148977086.648:1): initialized
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
0000:00:10.0: uhci_check_and_reset_hc: legsup = 0x2000
0000:00:10.0: Performing full reset
0000:00:10.1: uhci_check_and_reset_hc: legsup = 0x2000
0000:00:10.1: Performing full reset
0000:00:10.2: uhci_check_and_reset_hc: legsup = 0x2000
0000:00:10.2: Performing full reset
0000:00:10.3: uhci_check_and_reset_hc: legsup = 0x2000
0000:00:10.3: Performing full reset
Linux agpgart interface v0.101 (c) Dave Jones
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
floppy0: no floppy controllers found
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.0
PCI: VIA IRQ fixup for 0000:00:0f.0, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: ST3160021A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
hdd: ST340810A, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 >
hdd: max request size: 128KiB
hdd: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hdd: cache flushes not supported
hdd: hdd1 hdd2 < hdd5 > hdd3
hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
usbmon: debugfs is not available
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20
2006 UTC).
ALSA device list:
No soundcards found.
oprofile: using timer interrupt.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 5, 131072 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
ip_conntrack version 2.4 (4095 buckets, 32760 max) - 172 bytes per conntrack
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 152k freed
kjournald starting. Commit interval 5 seconds
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
Adding 2096472k swap on /dev/hdd3. Priority:-1 extents:1 across:2096472k
EXT3 FS on hda1, internal journal
lp0: using parport0 (interrupt-driven).
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
PCI: Found IRQ 11 for device 0000:00:0b.0
eth0: RealTek RTL-8029 found at 0xd000, IRQ 11, 00:C0:DF:F5:1A:C9.
PCI: Found IRQ 5 for device 0000:00:0c.0
PCI: Sharing IRQ 5 with 0000:00:10.4
gameport: ES137x is pci0000:00:0c.0/gameport0, io 0x200, speed 978kHz
input: Microsoft SideWinder Force Feedback Pro as /class/input/input2
USB Universal Host Controller Interface driver v2.3
PCI: Found IRQ 10 for device 0000:00:10.0
PCI: Sharing IRQ 10 with 0000:00:10.1
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: detected 2 ports
uhci_hcd 0000:00:10.0: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.0: Performing full reset
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 10, io base 0x0000dc00
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb1: SerialNumber: 0000:00:10.0
usb usb1: uevent
usb usb1: device is self-powered
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
uhci_hcd 0000:00:10.0: port 1 portsc 008a,00
hub 1-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
PCI: Found IRQ 10 for device 0000:00:10.1
PCI: Sharing IRQ 10 with 0000:00:10.0
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: detected 2 ports
uhci_hcd 0000:00:10.1: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.1: Performing full reset
drivers/usb/core/inode.c: creating file '002'
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 10, io base 0x0000e000
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.1
usb usb2: uevent
usb usb2: device is self-powered
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
drivers/usb/core/inode.c: creating file '001'
PCI: Found IRQ 11 for device 0000:00:10.2
PCI: Sharing IRQ 11 with 0000:00:10.3
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: detected 2 ports
uhci_hcd 0000:00:10.2: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.2: Performing full reset
drivers/usb/core/inode.c: creating file '003'
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 11, io base 0x0000e400
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.2
usb usb3: uevent
usb usb3: device is self-powered
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.0: port 2 portsc 018a,00
hub 1-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
drivers/usb/core/inode.c: creating file '001'
PCI: Found IRQ 11 for device 0000:00:10.3
PCI: Sharing IRQ 11 with 0000:00:10.2
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: detected 2 ports
uhci_hcd 0000:00:10.3: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.3: Performing full reset
drivers/usb/core/inode.c: creating file '004'
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 11, io base 0x0000e800
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.3
usb usb4: uevent
usb usb4: device is self-powered
usb usb4: configuration #1 chosen from 1 choice
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: uevent
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.1: port 1 portsc 008a,00
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
drivers/usb/core/inode.c: creating file '001'
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.1: port 2 portsc 018a,00
hub 2-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.2: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.2: port 2 portsc 008a,00
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
PCI: Found IRQ 5 for device 0000:00:10.4
PCI: Sharing IRQ 5 with 0000:00:0c.0
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: reset hcs_params 0x4208 dbg=0 cc=4 pcc=2 ordered !ppc ports=8
ehci_hcd 0000:00:10.4: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.4: MWI active
drivers/usb/core/inode.c: creating file '005'
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 5, io mem 0xe2000000
ehci_hcd 0000:00:10.4: reset command 080002 (park)=0 ithresh=8 period=1024 Reset
HALT
ehci_hcd 0000:00:10.4: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: default language 0x0409
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.16.18 ehci_hcd
usb usb5: SerialNumber: 0000:00:10.4
usb usb5: uevent
usb usb5: device is self-powered
usb usb5: configuration #1 chosen from 1 choice
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: uevent
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: Single TT
hub 5-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 5-0:1.0: power on to power good time: 20ms
hub 5-0:1.0: local power source is good
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.3: port 1 portsc 008a,00
hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
drivers/usb/core/inode.c: creating file '001'
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.3: port 2 portsc 018a,00
hub 4-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
uhci_hcd 0000:00:10.0: suspend_rh (auto-stop)
uhci_hcd 0000:00:10.1: suspend_rh (auto-stop)
uhci_hcd 0000:00:10.2: suspend_rh (auto-stop)
uhci_hcd 0000:00:10.3: suspend_rh (auto-stop)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
nvidia: module license 'NVIDIA' taints kernel.
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8762 Mon May 15 13:06:38 PDT 2006
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:10.4: port 1 full speed --> companion
ehci_hcd 0000:00:10.4: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
uhci_hcd 0000:00:10.0: wakeup_rh (auto-start)
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:10.0: port 1 portsc 0093,00
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
uhci_hcd 0000:00:10.0: port 1 portsc 008a,00
uhci_hcd 0000:00:10.0: port 1 portsc 0088,00
uhci_hcd 0000:00:10.0: port 1 portsc 0088,00
uhci_hcd 0000:00:10.0: port 1 portsc 0088,00
uhci_hcd 0000:00:10.0: port 1 portsc 0088,00
hub 1-0:1.0: debounce: port 1: total 150ms stable 100ms status 0x100
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001002 POWER sig=se0 CSC
hub 5-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:10.0: port 1 portsc 0088,00
hub 1-0:1.0: port 1 enable change, status 00000100
uhci_hcd 0000:00:10.0: suspend_rh (auto-stop)
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: default language 0x0409
usb 5-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-1: Product: External HDD
usb 5-1: Manufacturer: Western Digital
usb 5-1: SerialNumber: 57442D574D414E5531303836373034
usb 5-1: uevent
usb 5-1: device is self-powered
usb 5-1: configuration #1 chosen from 1 choice
usb 5-1: adding 5-1:1.0 (config #1, interface 0)
usb 5-1:1.0: uevent
drivers/usb/core/inode.c: creating file '003'
Initializing USB Mass Storage driver...
usb-storage 5-1:1.0: usb_probe_interface
usb-storage 5-1:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: WD Model: 4000KS External Rev: 101a
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 11 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 11 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
More information about the Bugme-new
mailing list