[Bugme-new] [Bug 8856] New: ata3: port is slow to respond,
please be patient (Status 0xd1)
bugme-daemon at bugzilla.kernel.org
bugme-daemon at bugzilla.kernel.org
Tue Aug 7 09:14:48 PDT 2007
http://bugzilla.kernel.org/show_bug.cgi?id=8856
Summary: ata3: port is slow to respond, please be patient (Status
0xd1)
Product: IO/Storage
Version: 2.5
KernelVersion: 2.6.21.5,2.6.22.1
Platform: All
OS/Version: Linux
Tree: Mainline
Status: NEW
Severity: high
Priority: P1
Component: Serial ATA
AssignedTo: jgarzik at pobox.com
ReportedBy: maxnux at yahoo.com.ar
CC: maxnux at yahoo.com.ar
Most recent kernel where this bug did not occur:
Distribution:Salckware 12
Hardware Environment:Notebook with barebone z96f t2250, 1g ram ,hd samsung 120g
,last bios
Software Environment:
Problem Description:
if use ide driver no problem but no dma , when use sata driver get this error
sometimes
ata3.01: qc timeout (cmd 0xa0)
ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.01: cmd a0/00:00:00:00:20/00:00:00:00:00/b0 tag 0 cdb 0x25 data 8 in
res 51/20:03:00:00:00/00:00:00:00:00/b0 Emask 0x5 (timeout)
ata3: port is slow to respond, please be patient (Status 0xd1)
ata3: device not ready (errno=-16), forcing hardreset
ata3: soft resetting port
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
when i disable apic (noapic option on boot time), the error takes place less
times.
when the error ocurr , S.O. hang for 30 seconds
full dmesg and lspci
Linux version 2.6.22.1-smp (root at maxnux-n) (gcc version 4.1.2) #2 SMP Sun Aug 5
16:19:10 ART 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000004f7b0000 (usable)
BIOS-e820: 000000004f7b0000 - 000000004f7be000 (ACPI data)
BIOS-e820: 000000004f7be000 - 000000004f7f0000 (ACPI NVS)
BIOS-e820: 000000004f7f0000 - 000000004f800000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
375MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 325552) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 325552
early_node_map[1] active PFN ranges
0: 0 -> 325552
On node 0 totalpages: 325552
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 751 pages used for memmap
HighMem zone: 95425 pages, LIFO batch:31
DMI present.
ACPI: RSDP 000FB700, 0014 (r0 ACPIAM)
ACPI: RSDT 4F7B0000, 0034 (r1 A M I OEMRSDT 7000614 MSFT 97)
ACPI: FACP 4F7B0200, 0084 (r2 A M I OEMFACP 7000614 MSFT 97)
ACPI Warning (tbfadt-0434): Optional field "Pm2ControlBlock" has zero address
or length: 0000000000000820/0 [20070126]
ACPI: DSDT 4F7B0430, 6007 (r1 A0544 A0544000 0 INTL 20060113)
ACPI: FACS 4F7BE000, 0040
ACPI: APIC 4F7B0390, 005C (r1 A M I OEMAPIC 7000614 MSFT 97)
ACPI: MCFG 4F7B03F0, 003C (r1 A M I OEMMCFG 7000614 MSFT 97)
ACPI: OEMB 4F7BE040, 0060 (r1 A M I AMI_OEM 7000614 MSFT 97)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
ACPI: Skipping IOAPIC probe due to 'noapic' option.
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: TEMPLATE Product ID: APIC at: 0xFEE00000
I/O APIC #2 Version 32 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Allocating PCI resources starting at 50000000 (gap: 4f800000:af600000)
Built 1 zonelists. Total pages: 323009
Kernel command line: BOOT_IMAGE=Linux-2.6.22.1 ro root=801 ide1=noprobe
ide0=noprobe noapic
ide_setup: ide1=noprobe
ide_setup: ide0=noprobe
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1729.108 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1285160k/1302208k available (2691k kernel code, 15920k reserved, 1060k
data, 284k init, 384704k highmem)
virtual kernel memory layout:
fixmap : 0xffe17000 - 0xfffff000 (1952 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc04b2000 - 0xc04f9000 ( 284 kB)
.data : 0xc03a0ee1 - 0xc04aa264 (1060 kB)
.text : 0xc0100000 - 0xc03a0ee1 (2691 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3462.10 BogoMIPS (lpj=6924206)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189
00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c189
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0ca8)
CPU0: Intel Genuine Intel(R) CPU T2250 @ 1.73GHz stepping 08
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3458.29 BogoMIPS (lpj=6916591)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189
00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c189
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU T2250 @ 1.73GHz stepping 08
Total of 2 processors activated (6920.39 BogoMIPS).
APIC calibration not consistent with PM Timer: 116ms instead of 100ms
APIC delta adjusted to PM-Timer: 831246 (964305)
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=61
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
ACPI: RTC can wake from S4
pnp: 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
pnp: 00:08: iomem range 0x8c000000-0x8c01ffff has been reserved
pnp: 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
pnp: 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved
pnp: 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:09: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:0a: iomem range 0xe0000000-0xe3ffffff has been reserved
pnp: 00:0b: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0b: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:0b: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0b: iomem range 0x100000-0x4f7fffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:1c.0
IO window: c000-cfff
MEM window: fe700000-fe7fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: disabled.
MEM window: fe600000-fe6fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
IO window: b000-bfff
MEM window: fde00000-fe5fffff
PREFETCH window: bdf00000-bfefffff
PCI: Bridge: 0000:00:1e.0
IO window: d000-dfff
MEM window: fe800000-fe8fffff
PREFETCH window: 50000000-500fffff
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ
5
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1c.1[B] -> Link [LNKB] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:1c.2[C] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 482k freed
apm: BIOS not found.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 1536k, total
7872k
vesafb: mode is 1024x768x8, linelength=1024, pages=9
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide-floppy driver 0.99.newide
Loading iSCSI transport class v2.0-724.
ahci 0000:04:00.0: version 2.2
ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ
5
ahci 0000:04:00.0: AHCI 0001.0000 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
ahci 0000:04:00.0: flags: 64bit ncq pm led clo pmp pio slum part
PCI: Setting latency timer of device 0000:04:00.0 to 64
scsi0 : ahci
ata1: SATA max UDMA/133 cmd 0xf8814100 ctl 0x00000000 bmdma 0x00000000 irq 5
ata1: SATA link down (SStatus 0 SControl 300)
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 7 (level, low) -> IRQ
7
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi1 : ata_piix
scsi2 : ata_piix
ata2: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
ata3: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
ata3.00: ATA-7: SAMSUNG HM120JC, YL100-19, max UDMA/100
ata3.00: 234441648 sectors, multi 16: LBA48
ata3.01: ATAPI: TSSTcorpCD/DVDW TS-L632D, AS05, max UDMA/33
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/33
scsi 2:0:0:0: Direct-Access ATA SAMSUNG HM120JC YL10 PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2 sda3
sd 2:0:0:0: [sda] Attached SCSI disk
scsi 2:0:1:0: CD-ROM TSSTcorp CD/DVDW TS-L632D AS05 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:1:0: Attached scsi CD-ROM sr0
usbmon: debugfs is not available
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
input: AT Translated Set 2 keyboard as /class/input/input0
raid6: int32x1 553 MB/s
raid6: int32x2 631 MB/s
raid6: int32x4 508 MB/s
raid6: int32x8 470 MB/s
raid6: mmxx1 1584 MB/s
raid6: mmxx2 1780 MB/s
raid6: sse1x1 1183 MB/s
raid6: sse1x2 1641 MB/s
raid6: sse2x1 1821 MB/s
raid6: sse2x2 1996 MB/s
raid6: using algorithm sse2x2 (1996 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 4512.000 MB/sec
raid5: using function: pIII_sse (4512.000 MB/sec)
md: multipath personality registered for level -4
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel at redhat.com
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 284k freed
ReiserFS: sda1: found reiserfs format "3.6" with standard journal
ReiserFS: sda1: using ordered data mode
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
ReiserFS: sda1: replayed 331 transactions in 17 seconds
ReiserFS: sda1: Using r5 hash to sort names
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 3 (level, low) -> IRQ
3
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 3, io base 0x0000e400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Linux agpgart interface v0.102 (c) Dave Jones
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 7 (level, low) -> IRQ
7
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 7, io base 0x0000e480
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
sd 2:0:0:0: Attached scsi generic sg0 type 0
sr 2:0:1:0: Attached scsi generic sg1 type 5
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 11, io base 0x0000e800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
intel_rng: FWH not detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ
5
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 5, io base 0x0000e880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ
5
PCI: Setting latency timer of device 0000:00:1b.0 to 64
usb 1-1: configuration #1 chosen from 1 choice
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
usb 3-1: new full speed USB device using uhci_hcd and address 2
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 3 (level, low) -> IRQ
3
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
usb 3-1: configuration #1 chosen from 1 choice
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 3, io mem 0xfeb3fc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Bluetooth: HCI socket layer initialized
ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKD] -> GSI 7 (level, low) -> IRQ
7
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
eth0: RTL8169sc/8110sc at 0xf8848c00, 00:18:f3:cf:f0:4d, IRQ 11
ACPI: PCI Interrupt 0000:05:01.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ
5
usb 3-1: USB disconnect, address 2
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[5] MMIO=[fe8fe800-fe8fefff] Max
Packet=[2048] IR/IT contexts=[4/4]
sdhci: SDHCI controller found at 0000:05:01.1 [1180:0822] (rev 19)
ACPI: PCI Interrupt 0000:05:01.1[B] -> Link [LNKB] -> GSI 10 (level, low) ->
IRQ 10
mmc0: SDHCI at 0xfe8ff000 irq 10 DMA
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hiddev
usb 1-1: USB disconnect, address 2
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno at linux.intel.com>
ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.2.2d
ipw3945: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKB] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:03:00.0 to 64
ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection
usb 5-8: new high speed USB device using ehci_hcd and address 4
usb 5-8: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hci_usb
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Adding 1004052k swap on /dev/sda2. Priority:-1 extents:1 across:1004052k
usb 1-1: new low speed USB device using uhci_hcd and address 3
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0180003763ee9]
usb 1-1: configuration #1 chosen from 1 choice
input: Genius NetScroll + Traveler as /class/input/input1
input: USB HID v1.10 Mouse [Genius NetScroll + Traveler] on usb-0000:00:1d.0-1
usb 3-1: new full speed USB device using uhci_hcd and address 3
usb 3-1: configuration #1 chosen from 1 choice
input: PC Speaker as /class/input/input2
input: ImPS/2 Synaptics TouchPad as /class/input/input3
lp: driver loaded but no devices found
Capability LSM initialized
ACPI: AC Adapter [AC0] (on-line)
Asus Laptop ACPI Extras version 0.30
Error calling BSTS
unsupported model Z96F, trying default values
send /proc/acpi/dsdt to the developers
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [SLPB]
input: Power Button (CM) as /class/input/input7
ACPI: Power Button (CM) [PWRB]
ACPI: SSDT 4F7B6440, 043D (r1 AMI CPU1PM 1 INTL 20060113)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Warning (tbutils-0158): Incorrect checksum in table [SSDT] - 2D, should
be 24 [20070126]
ACPI: SSDT 4F7B6880, 043D (r1 AMI CPU2PM 1 INTL 20060113)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI: Thermal Zone [TZ00] (33 C)
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
r8169: eth0: link up
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
eth0: no IPv6 routers present
ipw3945: Detected geography ABG (11 802.11bg channels, 13 802.11a channels)
ADDRCONF(NETDEV_UP): eth1: link is not ready
ieee80211_crypt: registered algorithm 'WEP'
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ
5
[drm] Initialized i915 1.6.0 20060119 on minor 0
usb 1-1: USB disconnect, address 3
ata3.01: qc timeout (cmd 0xa0)
ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.01: cmd a0/00:00:00:00:20/00:00:00:00:00/b0 tag 0 cdb 0x25 data 8 in
res 51/20:03:00:00:00/00:00:00:00:00/b0 Emask 0x5 (timeout)
ata3: port is slow to respond, please be patient (Status 0xd1)
ata3: device not ready (errno=-16), forcing hardreset
ata3: soft resetting port
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
ata3.01: qc timeout (cmd 0xa0)
ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.01: cmd a0/00:00:00:00:20/00:00:00:00:00/b0 tag 0 cdb 0x25 data 8 in
res 51/20:03:00:00:00/00:00:00:00:00/b0 Emask 0x5 (timeout)
ata3: port is slow to respond, please be patient (Status 0xd0)
ata3: device not ready (errno=-16), forcing hardreset
ata3: soft resetting port
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
usb 3-2: new low speed USB device using uhci_hcd and address 4
usb 3-2: configuration #1 chosen from 1 choice
input: Genius NetScroll + Traveler as /class/input/input8
input: USB HID v1.10 Mouse [Genius NetScroll + Traveler] on usb-0000:00:1d.2-2
ata3.01: qc timeout (cmd 0xa0)
ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.01: cmd a0/00:00:00:00:20/00:00:00:00:00/b0 tag 0 cdb 0x25 data 8 in
res 51/20:03:00:00:00/00:00:00:00:00/b0 Emask 0x5 (timeout)
ata3: port is slow to respond, please be patient (Status 0xd1)
ata3: device not ready (errno=-16), forcing hardreset
ata3: soft resetting port
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
ipw3945: Error sending LEDS_CMD: time out after 500ms.
usb 3-2: USB disconnect, address 4
usb 3-2: new low speed USB device using uhci_hcd and address 5
usb 3-2: configuration #1 chosen from 1 choice
input: Genius NetScroll + Traveler as /class/input/input9
input: USB HID v1.10 Mouse [Genius NetScroll + Traveler] on usb-0000:00:1d.2-2
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and
945GT Express Memory Controller Hub (rev 03)
Subsystem: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT
Express Memory Controller Hub
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS,
943/940GML Express Integrated Graphics Controller (rev 03) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device 1252
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at feb80000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at ec00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at feb40000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS, 943/940GML
Express Integrated Graphics Controller (rev 03)
Subsystem: ASUSTeK Computer Inc. Unknown device 1252
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fea80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition
Audio Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 1343
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at feb38000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1
(rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe700000-fe7fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <256ns, L1 <4us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2
(rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fe600000-fe6fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3
(rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fde00000-fe5fffff
Prefetchable memory behind bridge: 00000000bdf00000-00000000bfefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 3
Region 4: I/O ports at e400 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 7
Region 4: I/O ports at e480 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at e800 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at e880 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 3
Region 0: Memory at feb3fc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if
01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe800000-fe8fffff
Prefetchable memory behind bridge: 0000000050000000-00000000500fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Unknown device 1347
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge
(rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE
Controller (rev 02) (prog-if 80 [Master])
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 7
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 7
Region 4: I/O ports at 0400 [size=32]
03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network
Connection (rev 02)
Subsystem: Intel Corporation Unknown device 1000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe6ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
04:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI
Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device 1348
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at cc00 [size=8]
Region 1: I/O ports at c880 [size=4]
Region 2: I/O ports at c800 [size=8]
Region 3: I/O ports at c480 [size=4]
Region 4: I/O ports at c400 [size=16]
Region 5: Memory at fe7fe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Express Legacy Endpoint IRQ 1
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 1
Link: Latency L0s <1us, L1 <16us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
05:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (prog-if
10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fe8fe800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
05:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822
SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin B routed to IRQ 10
Region 0: Memory at fe8ff000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
05:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: Memory at fe8ff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
05:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter
(rev 0a)
Subsystem: ASUSTeK Computer Inc. Unknown device 1347
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at fe8ff800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
05:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC
Gigabit Ethernet (rev 10)
Subsystem: ASUSTeK Computer Inc. Unknown device 1345
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at fe8ffc00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Steps to reproduce:
--
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
More information about the Bugme-new
mailing list