[Linux-kernel-mentees] [PATCH v5 3/3] net: fddi: skfp: Remove unused private PCI definitions
Puranjay Mohan
puranjay12 at gmail.com
Fri Jun 21 15:40:37 UTC 2019
Remove unused private PCI definitions from skfbi.h because generic PCI
symbols are already included from pci_regs.h.
Signed-off-by: Puranjay Mohan <puranjay12 at gmail.com>
---
drivers/net/fddi/skfp/h/skfbi.h | 225 +-------------------------------
1 file changed, 1 insertion(+), 224 deletions(-)
diff --git a/drivers/net/fddi/skfp/h/skfbi.h b/drivers/net/fddi/skfp/h/skfbi.h
index 5f9b631e7515..480795681719 100644
--- a/drivers/net/fddi/skfp/h/skfbi.h
+++ b/drivers/net/fddi/skfp/h/skfbi.h
@@ -24,49 +24,6 @@
* (ML) = only defined for Monalisa
*/
-/*
- * Configuration Space header
- */
-#define PCI_VENDOR_ID 0x00 /* 16 bit Vendor ID */
-#define PCI_DEVICE_ID 0x02 /* 16 bit Device ID */
-#define PCI_COMMAND 0x04 /* 16 bit Command */
-#define PCI_STATUS 0x06 /* 16 bit Status */
-#define PCI_REVISION_ID 0x08 /* 8 bit Revision ID */
-#define PCI_CLASS_CODE 0x09 /* 24 bit Class Code */
-#define PCI_CACHE_LSZ 0x0c /* 8 bit Cache Line Size */
-#define PCI_LAT_TIM 0x0d /* 8 bit Latency Timer */
-#define PCI_HEADER_T 0x0e /* 8 bit Header Type */
-#define PCI_BIST 0x0f /* 8 bit Built-in selftest */
-#define PCI_BASE_1ST 0x10 /* 32 bit 1st Base address */
-#define PCI_BASE_2ND 0x14 /* 32 bit 2nd Base address */
-/* Byte 18..2b: Reserved */
-#define PCI_SUB_VID 0x2c /* 16 bit Subsystem Vendor ID */
-#define PCI_SUB_ID 0x2e /* 16 bit Subsystem ID */
-#define PCI_BASE_ROM 0x30 /* 32 bit Expansion ROM Base Address */
-/* Byte 34..33: Reserved */
-#define PCI_CAP_PTR 0x34 /* 8 bit (ML) Capabilities Ptr */
-/* Byte 35..3b: Reserved */
-#define PCI_IRQ_LINE 0x3c /* 8 bit Interrupt Line */
-#define PCI_IRQ_PIN 0x3d /* 8 bit Interrupt Pin */
-#define PCI_MIN_GNT 0x3e /* 8 bit Min_Gnt */
-#define PCI_MAX_LAT 0x3f /* 8 bit Max_Lat */
-/* Device Dependent Region */
-#define PCI_OUR_REG 0x40 /* 32 bit (DV) Our Register */
-#define PCI_OUR_REG_1 0x40 /* 32 bit (ML) Our Register 1 */
-#define PCI_OUR_REG_2 0x44 /* 32 bit (ML) Our Register 2 */
-/* Power Management Region */
-#define PCI_PM_CAP_ID 0x48 /* 8 bit (ML) Power Management Cap. ID */
-#define PCI_PM_NITEM 0x49 /* 8 bit (ML) Next Item Ptr */
-#define PCI_PM_CAP_REG 0x4a /* 16 bit (ML) Power Management Capabilities */
-#define PCI_PM_CTL_STS 0x4c /* 16 bit (ML) Power Manag. Control/Status */
-/* Byte 0x4e: Reserved */
-#define PCI_PM_DAT_REG 0x4f /* 8 bit (ML) Power Manag. Data Register */
-/* VPD Region */
-#define PCI_VPD_CAP_ID 0x50 /* 8 bit (ML) VPD Cap. ID */
-#define PCI_VPD_NITEM 0x51 /* 8 bit (ML) Next Item Ptr */
-#define PCI_VPD_ADR_REG 0x52 /* 16 bit (ML) VPD Address Register */
-#define PCI_VPD_DAT_REG 0x54 /* 32 bit (ML) VPD Data Register */
-/* Byte 58..ff: Reserved */
/*
* I2C Address (PCI Config)
@@ -76,176 +33,10 @@
*/
#define I2C_ADDR_VPD 0xA0 /* I2C address for the VPD EEPROM */
-/*
- * Define Bits and Values of the registers
- */
-/* PCI_VENDOR_ID 16 bit Vendor ID */
-/* PCI_DEVICE_ID 16 bit Device ID */
-/* Values for Vendor ID and Device ID shall be patched into the code */
-/* PCI_COMMAND 16 bit Command */
-#define PCI_FBTEN 0x0200 /* Bit 9: Fast Back-To-Back enable */
-#define PCI_SERREN 0x0100 /* Bit 8: SERR enable */
-#define PCI_ADSTEP 0x0080 /* Bit 7: Address Stepping */
-#define PCI_PERREN 0x0040 /* Bit 6: Parity Report Response enable */
-#define PCI_VGA_SNOOP 0x0020 /* Bit 5: VGA palette snoop */
-#define PCI_MWIEN 0x0010 /* Bit 4: Memory write an inv cycl ena */
-#define PCI_SCYCEN 0x0008 /* Bit 3: Special Cycle enable */
-#define PCI_BMEN 0x0004 /* Bit 2: Bus Master enable */
-#define PCI_MEMEN 0x0002 /* Bit 1: Memory Space Access enable */
-#define PCI_IOEN 0x0001 /* Bit 0: IO Space Access enable */
-
-/* PCI_STATUS 16 bit Status */
-#define PCI_PERR 0x8000 /* Bit 15: Parity Error */
-#define PCI_SERR 0x4000 /* Bit 14: Signaled SERR */
-#define PCI_RMABORT 0x2000 /* Bit 13: Received Master Abort */
-#define PCI_RTABORT 0x1000 /* Bit 12: Received Target Abort */
-#define PCI_STABORT 0x0800 /* Bit 11: Sent Target Abort */
-#define PCI_DEVSEL 0x0600 /* Bit 10..9: DEVSEL Timing */
-#define PCI_DEV_FAST (0<<9) /* fast */
-#define PCI_DEV_MEDIUM (1<<9) /* medium */
-#define PCI_DEV_SLOW (2<<9) /* slow */
-#define PCI_DATAPERR 0x0100 /* Bit 8: DATA Parity error detected */
-#define PCI_FB2BCAP 0x0080 /* Bit 7: Fast Back-to-Back Capability */
-#define PCI_UDF 0x0040 /* Bit 6: User Defined Features */
-#define PCI_66MHZCAP 0x0020 /* Bit 5: 66 MHz PCI bus clock capable */
-#define PCI_NEWCAP 0x0010 /* Bit 4: New cap. list implemented */
#define PCI_ERRBITS (PCI_STATUS_DETECTED_PARITY | PCI_STATUS_SIG_SYSTEM_ERROR | PCI_STATUS_REC_MASTER_ABORT | PCI_STATUS_SIG_TARGET_ABORT | PCI_STATUS_PARITY)
-/* PCI_REV_ID 8 bit Revision ID */
-/* PCI_CLASS_CODE 24 bit Class Code */
-/* Byte 2: Base Class (02) */
-/* Byte 1: SubClass (02) */
-/* Byte 0: Programming Interface (00) */
-
-/* PCI_CACHE_LSZ 8 bit Cache Line Size */
-/* Possible values: 0,2,4,8,16 */
-
-/* PCI_LAT_TIM 8 bit Latency Timer */
-
-/* PCI_HEADER_T 8 bit Header Type */
-#define PCI_HD_MF_DEV 0x80 /* Bit 7: 0= single, 1= multi-func dev */
-#define PCI_HD_TYPE 0x7f /* Bit 6..0: Header Layout 0= normal */
-
-/* PCI_BIST 8 bit Built-in selftest */
-#define PCI_BIST_CAP 0x80 /* Bit 7: BIST Capable */
-#define PCI_BIST_ST 0x40 /* Bit 6: Start BIST */
-#define PCI_BIST_RET 0x0f /* Bit 3..0: Completion Code */
-
-/* PCI_BASE_1ST 32 bit 1st Base address */
-#define PCI_MEMSIZE 0x800L /* use 2 kB Memory Base */
-#define PCI_MEMBASE_BITS 0xfffff800L /* Bit 31..11: Memory Base Address */
-#define PCI_MEMSIZE_BIIS 0x000007f0L /* Bit 10..4: Memory Size Req. */
-#define PCI_PREFEN 0x00000008L /* Bit 3: Prefetchable */
-#define PCI_MEM_TYP 0x00000006L /* Bit 2..1: Memory Type */
-#define PCI_MEM32BIT (0<<1) /* Base addr anywhere in 32 Bit range */
-#define PCI_MEM1M (1<<1) /* Base addr below 1 MegaByte */
-#define PCI_MEM64BIT (2<<1) /* Base addr anywhere in 64 Bit range */
-#define PCI_MEMSPACE 0x00000001L /* Bit 0: Memory Space Indic. */
-
-/* PCI_SUB_VID 16 bit Subsystem Vendor ID */
-/* PCI_SUB_ID 16 bit Subsystem ID */
-
-/* PCI_BASE_ROM 32 bit Expansion ROM Base Address */
-#define PCI_ROMBASE 0xfffe0000L /* Bit 31..17: ROM BASE address (1st) */
-#define PCI_ROMBASZ 0x0001c000L /* Bit 16..14: Treat as BASE or SIZE */
-#define PCI_ROMSIZE 0x00003800L /* Bit 13..11: ROM Size Requirements */
-#define PCI_ROMEN 0x00000001L /* Bit 0: Address Decode enable */
-
-/* PCI_CAP_PTR 8 bit New Capabilities Pointers */
-/* PCI_IRQ_LINE 8 bit Interrupt Line */
-/* PCI_IRQ_PIN 8 bit Interrupt Pin */
-/* PCI_MIN_GNT 8 bit Min_Gnt */
-/* PCI_MAX_LAT 8 bit Max_Lat */
-/* Device Dependent Region */
-/* PCI_OUR_REG (DV) 32 bit Our Register */
-/* PCI_OUR_REG_1 (ML) 32 bit Our Register 1 */
- /* Bit 31..29: reserved */
-#define PCI_PATCH_DIR (3L<<27) /*(DV) Bit 28..27: Ext Patchs direction */
-#define PCI_PATCH_DIR_0 (1L<<27) /*(DV) Type of the pins EXT_PATCHS<1..0> */
-#define PCI_PATCH_DIR_1 (1L<<28) /* 0 = input */
- /* 1 = output */
-#define PCI_EXT_PATCHS (3L<<25) /*(DV) Bit 26..25: Extended Patches */
-#define PCI_EXT_PATCH_0 (1L<<25) /*(DV) */
-#define PCI_EXT_PATCH_1 (1L<<26) /* CLK for MicroWire (ML) */
-#define PCI_VIO (1L<<25) /*(ML) */
-#define PCI_EN_BOOT (1L<<24) /* Bit 24: Enable BOOT via ROM */
- /* 1 = Don't boot with ROM */
- /* 0 = Boot with ROM */
-#define PCI_EN_IO (1L<<23) /* Bit 23: Mapping to IO space */
-#define PCI_EN_FPROM (1L<<22) /* Bit 22: FLASH mapped to mem? */
- /* 1 = Map Flash to Memory */
- /* 0 = Disable all addr. decoding */
-#define PCI_PAGESIZE (3L<<20) /* Bit 21..20: FLASH Page Size */
-#define PCI_PAGE_16 (0L<<20) /* 16 k pages */
-#define PCI_PAGE_32K (1L<<20) /* 32 k pages */
-#define PCI_PAGE_64K (2L<<20) /* 64 k pages */
-#define PCI_PAGE_128K (3L<<20) /* 128 k pages */
- /* Bit 19: reserved (ML) and (DV) */
-#define PCI_PAGEREG (7L<<16) /* Bit 18..16: Page Register */
- /* Bit 15: reserved */
-#define PCI_FORCE_BE (1L<<14) /* Bit 14: Assert all BEs on MR */
-#define PCI_DIS_MRL (1L<<13) /* Bit 13: Disable Mem R Line */
-#define PCI_DIS_MRM (1L<<12) /* Bit 12: Disable Mem R multip */
-#define PCI_DIS_MWI (1L<<11) /* Bit 11: Disable Mem W & inv */
-#define PCI_DISC_CLS (1L<<10) /* Bit 10: Disc: cacheLsz bound */
-#define PCI_BURST_DIS (1L<<9) /* Bit 9: Burst Disable */
-#define PCI_BYTE_SWAP (1L<<8) /*(DV) Bit 8: Byte Swap in DATA */
-#define PCI_SKEW_DAS (0xfL<<4) /* Bit 7..4: Skew Ctrl, DAS Ext */
-#define PCI_SKEW_BASE (0xfL<<0) /* Bit 3..0: Skew Ctrl, Base */
-
-/* PCI_OUR_REG_2 (ML) 32 bit Our Register 2 (Monalisa only) */
-#define PCI_VPD_WR_TH (0xffL<<24) /* Bit 24..31 VPD Write Threshold */
-#define PCI_DEV_SEL (0x7fL<<17) /* Bit 17..23 EEPROM Device Select */
-#define PCI_VPD_ROM_SZ (7L<<14) /* Bit 14..16 VPD ROM Size */
- /* Bit 12..13 reserved */
-#define PCI_PATCH_DIR2 (0xfL<<8) /* Bit 8..11 Ext Patchs dir 2..5 */
-#define PCI_PATCH_DIR_2 (1L<<8) /* Bit 8 CS for MicroWire */
-#define PCI_PATCH_DIR_3 (1L<<9)
-#define PCI_PATCH_DIR_4 (1L<<10)
-#define PCI_PATCH_DIR_5 (1L<<11)
-#define PCI_EXT_PATCHS2 (0xfL<<4) /* Bit 4..7 Extended Patches */
-#define PCI_EXT_PATCH_2 (1L<<4) /* Bit 4 CS for MicroWire */
-#define PCI_EXT_PATCH_3 (1L<<5)
-#define PCI_EXT_PATCH_4 (1L<<6)
-#define PCI_EXT_PATCH_5 (1L<<7)
-#define PCI_EN_DUMMY_RD (1L<<3) /* Bit 3 Enable Dummy Read */
-#define PCI_REV_DESC (1L<<2) /* Bit 2 Reverse Desc. Bytes */
-#define PCI_USEADDR64 (1L<<1) /* Bit 1 Use 64 Bit Addresse */
-#define PCI_USEDATA64 (1L<<0) /* Bit 0 Use 64 Bit Data bus ext*/
-
-/* Power Management Region */
-/* PCI_PM_CAP_ID 8 bit (ML) Power Management Cap. ID */
-/* PCI_PM_NITEM 8 bit (ML) Next Item Ptr */
-/* PCI_PM_CAP_REG 16 bit (ML) Power Management Capabilities*/
-#define PCI_PME_SUP (0x1f<<11) /* Bit 11..15 PM Manag. Event Support*/
-#define PCI_PM_D2_SUB (1<<10) /* Bit 10 D2 Support Bit */
-#define PCI_PM_D1_SUB (1<<9) /* Bit 9 D1 Support Bit */
- /* Bit 6..8 reserved */
-#define PCI_PM_DSI (1<<5) /* Bit 5 Device Specific Init.*/
-#define PCI_PM_APS (1<<4) /* Bit 4 Auxialiary Power Src */
-#define PCI_PME_CLOCK (1<<3) /* Bit 3 PM Event Clock */
-#define PCI_PM_VER (7<<0) /* Bit 0..2 PM PCI Spec. version */
-
-/* PCI_PM_CTL_STS 16 bit (ML) Power Manag. Control/Status */
-#define PCI_PME_STATUS (1<<15) /* Bit 15 PFA doesn't sup. PME#*/
-#define PCI_PM_DAT_SCL (3<<13) /* Bit 13..14 dat reg Scaling factor */
-#define PCI_PM_DAT_SEL (0xf<<9) /* Bit 9..12 PM data selector field */
- /* Bit 7.. 2 reserved */
-#define PCI_PM_STATE (3<<0) /* Bit 0.. 1 Power Management State */
-#define PCI_PM_STATE_D0 (0<<0) /* D0: Operational (default) */
-#define PCI_PM_STATE_D1 (1<<0) /* D1: not supported */
-#define PCI_PM_STATE_D2 (2<<0) /* D2: not supported */
-#define PCI_PM_STATE_D3 (3<<0) /* D3: HOT, Power Down and Reset */
-
-/* PCI_PM_DAT_REG 8 bit (ML) Power Manag. Data Register */
-/* VPD Region */
-/* PCI_VPD_CAP_ID 8 bit (ML) VPD Cap. ID */
-/* PCI_VPD_NITEM 8 bit (ML) Next Item Ptr */
-/* PCI_VPD_ADR_REG 16 bit (ML) VPD Address Register */
-#define PCI_VPD_FLAG (1<<15) /* Bit 15 starts VPD rd/wd cycle*/
-
-/* PCI_VPD_DAT_REG 32 bit (ML) VPD Data Register */
+
/*
* Control Register File:
@@ -873,20 +664,6 @@
#define T3_MUX (3<<2) /* Bit 3..2: Mux position */
#define T3_VRAM (3<<0) /* Bit 1..0: Virtual RAM buffer Address */
-/* PCI card IDs */
-/*
- * Note: The following 4 byte definitions shall not be used! Use OEM Concept!
- */
-#define PCI_VEND_ID0 0x48 /* PCI vendor ID (SysKonnect) */
-#define PCI_VEND_ID1 0x11 /* PCI vendor ID (SysKonnect) */
- /* (High byte) */
-#define PCI_DEV_ID0 0x00 /* PCI device ID */
-#define PCI_DEV_ID1 0x40 /* PCI device ID (High byte) */
-
-/*#define PCI_CLASS 0x02*/ /* PCI class code: network device */
-#define PCI_NW_CLASS 0x02 /* PCI class code: network device */
-#define PCI_SUB_CLASS 0x02 /* PCI subclass ID: FDDI device */
-#define PCI_PROG_INTFC 0x00 /* PCI programming Interface (=0) */
/*
* address transmission from logical to physical offset address on board
--
2.21.0
More information about the Linux-kernel-mentees
mailing list